Help with setup on 600 for new user

Only for the discussion of the Minelab Equinox series of metal detector within this forum.
Post Reply
Crewesader
Posts: 22
Joined: Tue Sep 04, 2018 3:03 am
Been thanked: 2 times

Help with setup on 600 for new user

Post by Crewesader » Fri Sep 14, 2018 3:40 pm

I have dug more iron and foil reading 5 to 15 than ever with my Safari, I am not very technical hence my choice of Safari I obviously have it setup wrong I ( my 600 ) can anyone help me with a basic setup without going through advanced settings I have a learning curve ahead of me regarding the tones and TIDs but any pointers would be appreciated thanks in advance Lez



User avatar
Oxgirl36
Moderator
Posts: 9655
Joined: Sun Jul 10, 2016 6:54 pm
Location: Oxfordshire
Has thanked: 3819 times
Been thanked: 4174 times

Re: Help with setup on 600 for new user

Post by Oxgirl36 » Fri Sep 14, 2018 3:47 pm

This thread might help as assuming the 600 and 800 are pretty much the same set up...

viewtopic.php?f=291&t=104235

If not look through this forum as there is loads of great advice on here already ::g
Carpe vinum

XP Deus !!£$ I use the HOT programme on 17khz, reactivity at 2.5 on v5.21 with the X35 11” coil

Hammered silver 2019 - 14 x;

User avatar
fred
Posts: 9519
Joined: Wed Dec 10, 2014 6:15 pm
Location: Kent
Has thanked: 2031 times
Been thanked: 5337 times

Re: Help with setup on 600 for new user

Post by fred » Fri Sep 14, 2018 3:57 pm

Crewesader wrote:
Fri Sep 14, 2018 3:40 pm
I have dug more iron and foil reading 5 to 15 than ever with my Safari, I am not very technical hence my choice of Safari I obviously have it setup wrong I ( my 600 ) can anyone help me with a basic setup without going through advanced settings I have a learning curve ahead of me regarding the tones and TIDs but any pointers would be appreciated thanks in advance Lez
You will certainly dig more iron unless you adjust the Iron Bias, which is an advanced setting! Everything else can probably wait. Just ike the Safari you ave to decide whether to dig foil or not. You can do this by looking at the numbers or by rejecting the numbers where foil tends to appear. :D
Equinox 800 x2

Crewesader
Posts: 22
Joined: Tue Sep 04, 2018 3:03 am
Been thanked: 2 times

Re: Help with setup on 600 for new user

Post by Crewesader » Fri Sep 14, 2018 4:19 pm

What number would you suggest for the iron bias Fred ?

Crewesader
Posts: 22
Joined: Tue Sep 04, 2018 3:03 am
Been thanked: 2 times

Re: Help with setup on 600 for new user

Post by Crewesader » Fri Sep 14, 2018 4:31 pm

What number would you suggest for the iron bias Fred ?

User avatar
Bargeman
Posts: 2189
Joined: Sun Jan 22, 2017 12:25 pm
Location: Newbury
Has thanked: 860 times
Been thanked: 1280 times
Contact:

Re: Help with setup on 600 for new user

Post by Bargeman » Fri Sep 14, 2018 4:34 pm

2 would be a good start, if you have 2 on the 600



BM [:)

Walk that line, torn apart
spend your whole life trying.
Ride that train, free your heart,
it's midnight up in Harlem.

Midnight in Harlem, Tedeschi Trucks Band

User avatar
fred
Posts: 9519
Joined: Wed Dec 10, 2014 6:15 pm
Location: Kent
Has thanked: 2031 times
Been thanked: 5337 times

Re: Help with setup on 600 for new user

Post by fred » Fri Sep 14, 2018 4:41 pm

Crewesader wrote:
Fri Sep 14, 2018 4:31 pm
What number would you suggest for the iron bias Fred ?
On the 600 it should be set at 1 to start with, which equates to about 2 on the 800. ::g
Last edited by fred on Fri Sep 14, 2018 4:43 pm, edited 2 times in total.
Equinox 800 x2

Doyoudigitman
Posts: 276
Joined: Sun Jun 11, 2017 7:24 pm
Has thanked: 38 times
Been thanked: 150 times

Re: Help with setup on 600 for new user

Post by Doyoudigitman » Fri Sep 14, 2018 4:42 pm

On the 800 I use 2 r 3 don't know what that is on the 600!
You will definitely have to set the machine above 0 until
You get your head around what the machine is telling you!! ::g

User avatar
Bargeman
Posts: 2189
Joined: Sun Jan 22, 2017 12:25 pm
Location: Newbury
Has thanked: 860 times
Been thanked: 1280 times
Contact:

Re: Help with setup on 600 for new user

Post by Bargeman » Fri Sep 14, 2018 5:18 pm

fred wrote:
Fri Sep 14, 2018 4:41 pm
Crewesader wrote:
Fri Sep 14, 2018 4:31 pm
What number would you suggest for the iron bias Fred ?
On the 600 it should be set at 1 to start with, which equates to about 2 on the 800. ::g
That's it Fred, I was at work so couldn't remember the settings ::g



BM [:)

Walk that line, torn apart
spend your whole life trying.
Ride that train, free your heart,
it's midnight up in Harlem.

Midnight in Harlem, Tedeschi Trucks Band

Crewesader
Posts: 22
Joined: Tue Sep 04, 2018 3:03 am
Been thanked: 2 times

Re: Help with setup on 600 for new user

Post by Crewesader » Mon Oct 01, 2018 3:11 am

That's all folks !!!! Up and running with my 600 couldn't be happier I feel if I walk over it I will find it my French no 2 my C.T. and my Safari are all going on an auction site quickly before the truth about this machine is common knowledge !!!! P.S. don't tell people in Cheshire Lez

Post Reply

Return to “Minelab Equinox Forum”