Etrac advice

Only for the discussion of the Minelab E-TRAC metal detecting within this forum.
Post Reply
The caretaker
Posts: 61
Joined: Sat Jul 09, 2016 4:01 pm
Location: Sunderland Tyne and Wear
Has thanked: 64 times
Been thanked: 26 times

Etrac advice

Post by The caretaker » Mon Nov 12, 2018 6:49 pm

Bought a new etrac last week. Used it on Sunday for the first time I was using a safari before I boughtit. My question to you who are used to using the etrac is will I have more success using it in minelab preset coin mode or just turning the machine on doing a ground balance then press detect as I don't want to do any adjustments until I get to know the machine over time. On Sunday I just turned on done the ground balance then pressed detect I did find a Edward the 1st silver penny.
Your advice and comments would be appreciated. Thanks
It is hammered coins I am hoping to find


Minelab safari
Minelab e-trac

User avatar
Allectus
Posts: 25088
Joined: Tue Oct 25, 2011 8:37 am
Location: Essexshire ;-)
Has thanked: 552 times
Been thanked: 3179 times

Re: Etrac advice

Post by Allectus » Mon Nov 12, 2018 8:58 pm

You'll have more success binning the set modes...far too much discrim on those!

Multi-tone conductive is the way to go with everything maxed out(or very near) is the way to go(imo)

Brilliant machine!! ::g ::g

A ;)
British by Birth - English by the Grace Of God.

stargazer
Posts: 2826
Joined: Thu Jul 08, 2010 4:21 am
Location: Rochdale
Has thanked: 12 times
Been thanked: 78 times

Re: Etrac advice

Post by stargazer » Tue Nov 13, 2018 12:54 am

As Tony said................don't bother with the set programmes. Stick with 'conductive' and the less 'descrim' the better .
The mighty Minelab Etrac !

I'm UBIQUE! RE

User avatar
Blackadder43
Moderator
Posts: 9237
Joined: Sun Feb 21, 2010 1:34 pm
Location: Somerset
Has thanked: 491 times
Been thanked: 469 times

Re: Etrac advice

Post by Blackadder43 » Tue Nov 13, 2018 12:58 am

Playing devils advocate
I could never get on with conductive sounds
I am old school and used to my iron sounding like a grunt and not like a squealing hammy
I always used 2 or 3 tone ferrous, which was basically switch on, 3 tones, next to nothing in discrim, ground balanced and as much sensitivity as your ears could handle
Oh and i always manually chose channel 2 for the noise cancel, according to one of the minelab techies it was/is the best channel

Either way i agree with the others and steer clear of any factory presets as they are loaded with discrim and set up for the American Tot lot searchers
When you are right no one remembers; when you are wrong no one forgets

User avatar
Allectus
Posts: 25088
Joined: Tue Oct 25, 2011 8:37 am
Location: Essexshire ;-)
Has thanked: 552 times
Been thanked: 3179 times

Re: Etrac advice

Post by Allectus » Tue Nov 13, 2018 8:13 am

Also, I remember really struggling with the ET to decipher what was what until I used Target Response 'Smooth'....What a revelation that was!

Using the smooth setting really sorted the wheat from the chaff by 'grabbing & holding' a non ferrous target amongst the 'noise'.

One of the most important settings imo! ::g

A ;)
British by Birth - English by the Grace Of God.

clint
Posts: 3739
Joined: Tue Jun 28, 2011 9:12 pm
Location: Wrexham
Has thanked: 4 times
Been thanked: 17 times

Re: Etrac advice

Post by clint » Mon Jan 14, 2019 9:24 am

I would also add....trust what it's telling you in terms of sound rather than numbers. Close iron to a target will drag the Fe value down. Dropping the sens doesn't necessarily mean dropping the depth...it means you're just reading less of everything including background noise. Get a harness. Be prepared to dig....take your time...the etrac book by Sabisch is worth a read.
Enjoy!
Clint
Etrac.13" Ultimate Coil.CP3 TT`s
8x6 sef
Euroace.
Deteknix Pointer,camo,oh yeah! ...does what it says on the box..
Garrett Propointer..ok...(now it's fixed!)
Jeff`s big tool!

User avatar
Wigeon
Posts: 234
Joined: Mon Feb 06, 2017 5:03 pm
Location: North Cambs
Has thanked: 103 times
Been thanked: 106 times

Re: Etrac advice

Post by Wigeon » Mon Jan 14, 2019 2:36 pm

Some excellent advice already given above.

When I first got my Etrac over two years ago, I found it necessary to stick with the 'coins' programme for several weeks.

The Etrac can chirp like a canary on acid when used at full throttle with minimal discrimination. It can do one's head in until you get used to it and its controls.

Smooth response is a definite plus but once again took me a little while to get used to.

I took a careful, progressive approach that worked for me. A very good machine.
I hope you enjoy using it. ::g
Minelab E-Trac. XP Goldmaxx power v4. Garret carrot. Evolution spade.

Post Reply

Return to “Minelab E-TRAC Forum”