no light on coil after updating to v4 firmware
I had to return my coil for replacement!
Minelab Equinox 800, Field 2.
Minelab CTX3030
Minelab Profind-25
Auto+3, Ferrous-Coin, Long Sounds, Auto GB ON.
Minelab CTX3030
Minelab Profind-25
Auto+3, Ferrous-Coin, Long Sounds, Auto GB ON.
- oldartefact
- Posts: 12242
- Joined: Sun Dec 30, 2012 12:31 am
- Location: Gods own county - numero uno!
- Has thanked: 3113 times
- Been thanked: 3387 times
Was out on a dig today, and there was an almighty bang, immediate thought was that some idiot had just pulled the pin on a grenade, and then it dawned on us ... could only have been another V4 update ... meeting its maker!






Imagine there is no heaven, only sky above us.
I have called Regton's this morning and spoke to Nigel who was very helpful
Have been advised to put the coil on charge and then try the update while coil is still on charge
failing that I have to send the coil back to them.
I will try this later and keep you updated
Have been advised to put the coil on charge and then try the update while coil is still on charge
failing that I have to send the coil back to them.
I will try this later and keep you updated
- punka$$
- Posts: 216
- Joined: Sun May 06, 2012 4:54 pm
- Location: Hertfordshire
- Has thanked: 6 times
- Been thanked: 23 times
That's exactly what they told me to do, my 9 inch coil randomly rebooted after the update as well. Regton asked me to send them everything (2 coils, ws4 and remote) i was without a machine for about 3 or 4 weeks and had to wait an extra couple of weeks for the 11 to come back from francerst33 wrote: Tue Oct 03, 2017 6:12 pm Have tried updating coil while on charge and it is still dead
I'm sending the coil back to Regtons
Will update with outcome
all the gear, no idea!
Had a call from Regtons today
They are unable to get the coil to work
They have to send it back to XP and its going to take a couple of weeks
They will repair or replace depending on the problem
I will keep you posted
They are unable to get the coil to work
They have to send it back to XP and its going to take a couple of weeks
They will repair or replace depending on the problem

I will keep you posted
- oldartefact
- Posts: 12242
- Joined: Sun Dec 30, 2012 12:31 am
- Location: Gods own county - numero uno!
- Has thanked: 3113 times
- Been thanked: 3387 times
Thats very good news ... but does the update come with a manufacturers warning ... akin to those on fag packets "this update may give your coil a terminal condition"rst33 wrote: Mon Oct 16, 2017 7:15 pm Had a call from Regtons today
They are unable to get the coil to work
They have to send it back to XP and its going to take a couple of weeks
They will repair or replace depending on the problem![]()
I will keep you posted
Imagine there is no heaven, only sky above us.
Just to let you all know
I got the coil back from XP and the PCB board had failed (During the update I guess)
so the coil now has a new PCB board
it came back with version 3.2 so I then upgraded to V4 and it all worked fine
I got the coil back from XP and the PCB board had failed (During the update I guess)
so the coil now has a new PCB board
it came back with version 3.2 so I then upgraded to V4 and it all worked fine
I've seen this a couple of times. In the past month.
The way I managed to sort it was by placing the coil back on charge again.
it seems that the coil can get in a pickle.
Put it back on charge and within a couple of minutes it reinitialised and then connected showing full charge.
The way I managed to sort it was by placing the coil back on charge again.
it seems that the coil can get in a pickle.
Put it back on charge and within a couple of minutes it reinitialised and then connected showing full charge.
Who is online
Users browsing this forum: No registered users and 105 guests