Coil battery issue/calibration led

Forum group discussion of the XP Deus Metal Detector.
Post Reply
andyblue1974
Posts: 59
Joined: Sun Mar 31, 2019 2:13 pm
Been thanked: 20 times

Coil battery issue/calibration led

Post by andyblue1974 »

Hi there,I have the x35 11" coil, went out today for approximately 4 hours, noticed the coil had discharged half way, while the control box and headphones were full charge,they were all charged the night previous the same time,also noticed there didn't seem to be 20 flashes of the coil led calibration on start up.the coil is only 2 months old.. thanks ahead for your replys..
Oxgirl36

Post by Oxgirl36 »

Are you sure you had the charging clip on properly when you last charged it? It’s easy to do - I did it once before going on a dig - very embarrassing rl;
philsale
Posts: 116
Joined: Sun Dec 04, 2011 5:56 pm
Been thanked: 10 times

Post by philsale »

Hi the x35 coil does not flash like the black coil on start up and it easily missed, agree though if the charge is not lasting i would charge it up again and see what happens.
andyblue1974
Posts: 59
Joined: Sun Mar 31, 2019 2:13 pm
Been thanked: 20 times

Post by andyblue1974 »

Hi thanks for your replys,yes definitely the clip on properly,the light is solid when attached,that makes sense about the x35 coil led,it does two sets of 3 blinks for calibration, the old coil flashed quickly 20 times, obviously new coil, different technology, just unusual about the power drain, I did use the boost function,but I have in the past and it hasn't drained this fast..
User avatar
principia
Posts: 178
Joined: Sat Oct 12, 2013 11:52 am
Has thanked: 56 times
Been thanked: 52 times

Post by principia »

I do charge my coil as follows;
Charging till the light is blinking, disconnect than again charging 2x.
Than the coil is fully charged.
Chilgrove
Posts: 495
Joined: Fri Dec 05, 2014 5:14 pm
Has thanked: 2 times
Been thanked: 159 times

Post by Chilgrove »

I too notice that sometimes I can squeeze a little more current into my coils if I disconnect both remote and headphones when full charge is indicated. So by leaving the coil connected the LED will sometimes light on steady again.
I only have the basic black 9" and 11" coils but maybe this applies also to the HF coils. I vigorously rub my licked thumb over the coil contacts just before connection. I also always put something under the coil to prevent the clip connector fouling the floor beneath. I used to even find with my earlier coil connector that the slightest vibration nearby (eg dog walking close to charging coil) could result in good connection being lost.
Junior
Posts: 1521
Joined: Sun Sep 13, 2015 5:53 pm
Has thanked: 598 times
Been thanked: 486 times

Post by Junior »

I've found the black normal charge clips arnt the best I'm now on no 4 tend to kill the pins, now moved over to the green one from flee bay supp lifetime warranty I believe ::g
User avatar
Phil2401
Posts: 9571
Joined: Sun Dec 04, 2016 3:31 pm
Location: Surrey, originally Yorkshire
Has thanked: 5830 times
Been thanked: 4807 times

Post by Phil2401 »

Junior wrote: Tue Jun 18, 2019 10:30 am I've found the black normal charge clips arnt the best I'm now on no 4 tend to kill the pins, now moved over to the green one from flee bay supp lifetime warranty I believe ::g
Just to mention the green one is in the MDF shop - https://www.metaldetectingauction.com/s ... rging+clip

I've found it more reliable - like Oxgirl I've turned up to a dig once or twice with what I thought was a charged coil rl;

I also agree with Chilgrove's comments - charge all three together but when the phones & controller are full, leave the coil on charge for a bit longer. If you turn off the power then turn it back on again, it's surprising how often the coil light comes on solid again.

Phil
Quaerite et invenietis
Post Reply

Return to “XP DEUS Forum”

Who is online

Users browsing this forum: No registered users and 50 guests